ON THIS PAGE TYPES SIZES REQUEST A QUOTE QUESTIONS

Home / Products / Base plates

Steel and stainless plate · To your drawing

Steel base plates cut to drawing in Bình Dương

Steel and stainless base plates laser-cut to the exact size and hole positions on your drawing, with gussets, a column stub or anchor bars welded on when you need them. One piece or a thousand identical ones. Hot-dip galvanizing or painting through our partner plants on the same order.

Illustration of square laser-cut steel base plates with four bolt holes, stacked on a wooden pallet, one stack galvanized — ILLUSTRATION

Send a drawing, get a quote See the plate types

Up to 25 mm Steel and stainless plate

±0.1 mm Laser cutting tolerance

From 1 piece No minimum order

24 h Quote from your drawing

Base plates we are often asked for

A base plate is a thick steel plate that joins a structure: under a column, at a beam end, cast into concrete. We cut it exactly to the drawing, every hole and chamfer, then weld on whatever the drawing shows.

Column base plate

A square or rectangular plate with anchor-bolt holes, with a box section or pipe column welded on when needed.

Factory columns, pre-engineered steel buildings, canopies

Beam end plate

End plates and splice plates with rows of bolt holes that line up exactly between the two plates.

Beam-to-column and beam-to-beam connections

Gusseted base plate

A base plate with triangular stiffeners welded between the plate and the column for heavier loads. The gussets are laser-cut too, so they fit.

Heavily loaded columns, machine stands, light poles

Embed plate

A plate with anchor bars welded on, set in the formwork before the concrete is poured, for steelwork to be welded or bolted to later.

Cast into slabs, beams and concrete walls

Slotted plate

Slots instead of round holes so the position can be adjusted on site. Laser-cut slots are as clean as round holes.

Connections that need adjusting during erection

Stainless base plate

Square or round 304 stainless plates that need no galvanizing or paint, with bright edges cut under nitrogen.

Railings, glass canopies, coastal sites, food plants

Other shapes, hole patterns, chamfers and cut-outs are all cut from your drawing.

Common base plate sizes

The sizes most often used in factory buildings and steel structures. We cut any size to the drawing, on sheets up to 3,000 × 1,500 mm.

Size (mm)	Usual thickness	Holes
100 × 100	5–10 mm	4 holes Ø14
150 × 150	6–12 mm	4 holes Ø18
200 × 200	8–16 mm	4 holes Ø22
200 × 300	8–16 mm	4 holes Ø22
250 × 250	10–20 mm	4 holes Ø22
300 × 300	12–20 mm	4 holes Ø26
400 × 400	14–25 mm	8 holes Ø26

Priced from the drawing: material, thickness, number of holes, welded parts and quantity. Send the drawing on Zalo for a quote within 24 hours.

Bare, galvanized or painted

A base plate outdoors needs protecting from rust. We handle galvanizing and painting through partner plants, so you deal with one supplier.

Bare black steel

Delivered straight after cutting and welding. Suits plates cast into concrete or painted on site.

Hot-dip galvanized

A 45–85 µm zinc coat for plates exposed to the weather. Tell us about threaded holes, which are masked or re-tapped after galvanizing.

Powder coated

Any RAL colour for plates that stay on show, such as railing bases and decorative column feet.

Stainless 304

No coating needed. For coastal sites, damp areas and food plants.

Why laser-cut a base plate

Hand-drilled or punched plates drift by a few millimetres and the bolts will not go in on site. Laser cutting takes the holes straight from the drawing.

Holes where they should be. Holes are cut to the coordinates in the file, within ±0.1 mm, so the anchor bolts go straight in.

Every plate the same. A hundred or a thousand plates come off one cutting program, so any of them fits.

Any shape. Slots, chamfers, cut-outs, round or polygonal plates, with no tooling to make.

Clean edges. Straight edges with little burr, ready for welding or galvanizing.

Illustration of the corner of a thick laser-cut steel plate, a round bolt hole and a straight cut edge — ILLUSTRATION

How to order base plates

From drawing to delivery, we tell you what happens at each step.

01
Send the drawing

Send a DWG, DXF or PDF, or a photo of a hand sketch, on Zalo. Give the material, thickness, number and size of holes, and quantity.
02
Get a quote

A quote within 24 hours, with the lead time. If the drawing is missing something, we ask before cutting.
03
Cutting and welding

Laser cutting, then gussets, stubs or anchor bars welded on and holes tapped if the drawing calls for it.
04
Galvanizing or painting

When needed, the plates go to our partner plants and are checked when they come back.
05
Delivery

To your site or factory, with mill certificates on request.

Send your base plate drawing

Give the size, thickness, holes and quantity. If you have a file, send it on Zalo for a quote within 24 hours.

Request a quote

Replies within one business day. Your files stay confidential — NDA on request.

Or call +84 948 684 939

Name

Email or phone

Part details

By sending this, you agree to our privacy policy.

Base plate questions

Still stuck on a detail?

Send the drawing with your question — fastest way to a real answer.

+84 948 684 939 lienhe@tuanthinh.net

Ask an engineer

Replies within one business day

01 How thick can a base plate be?

We laser-cut steel and stainless plate up to 25 mm, on sheets up to 3,000 × 1,500 mm. For anything larger, we will explain how we would make it when we quote.

02 What is the smallest hole you can cut?

Keep a hole at least as wide as the plate is thick: on a 16 mm plate, holes from Ø16. For smaller holes, we will tell you how we would make them when we quote.

03 Do you take small orders?

Yes, from one piece. Larger orders cost less per plate, because they share one cutting program and nest more plates on each sheet.

04 Can you weld on the column, gussets or anchor bars?

Yes. Gussets, pipe, box section or anchor bars are TIG-welded in our shop to the drawing and delivered as a finished assembly.

05 Where is the hot-dip galvanizing done?

At a partner plant. We handle transport both ways and check the coating thickness when the plates come back. Tell us about threaded holes, because zinc fills the thread.

06 What if I have no drawing?

Write the plate size, thickness and hole positions and diameters on paper and send a photo on Zalo, or send a sample plate. We redraw it and send it for your approval before cutting.

Related processes

The processes a base plate goes through, in our shop and at our partners.

All services →

Need base plates for a project?

Send the drawing or the sizes on Zalo at 0948 684 939 for a quote within 24 hours.

Send a drawing Call +84 948 684 939